Pixracer PRO Autopilot Xracer PX4 Pixhawk Flight Controller M8N GPS Set RC Quadcopter Ardupilot
image_0

Pixracer PRO Autopilot Xracer PX4 Pixhawk Flight Controller M8N GPS Set RC Quadcopter Ardupilot

14:29#PIXRACER PRO

Regular price $463.99 Sale price$343.99 Save $120.00
/
Shipping calculated at checkout.

Color
  • In stock, ready to ship
  • Backordered, shipping soon

PIXRACER PRO


The Pixracer Pro has been designed primarily for the demanding requirements of small multicopters, but of course can be used on planes and other vehicles which require no more than 8 pwm outputs for controlling escs and motors.


Specifications

Specifications

mRo Pixracer Pro

Main Processor

32-bit STM32H743 Cortex M7 RISC core with FPU 460 MHz

IO Processor

No

RAM

1024 KB RAM

Flash

2 MB FRAM

Crypto / Hash Processor

No

Accelerometers / Gyros / Mags

Accelerometers / Gyros / Mags

Sensors – Dampened

Bosch BMI085 (6DOF) (internally vibration dampened)

Sensors

Invensense/TDK ICM-20602 (6DOF)
Invensense/TDK ICM-20948 (9DOF)

Internal Magnetometer

AK09916 inside ICM-20948

Barometer

Infineon DPS310 barometer (Very smooth and NO light sensitivity)

Interfaces and Protocols

6x UART (serial ports) [2x with HW flow control,1x FRSky Telemetry (D or X types), 2x General Purpose & 1x GPS+I2C].
 

1x PPM sum input signal
8x PWM outputs (all D-Shot capable)
1x RSSI (PWM or voltage) input
1x I2C
1x SPI
2x CAN
1x SWD (TC2030 Connector)
3x Ultra low-noise LDO voltage regulator

Supported RC input protocols:
Spektrum DSM / DSM2 / DSM-X® Satellite compatible input and binding.
Futaba S.BUS® & S.BUS2® compatible input.
FRSky Telemetry port output.
Graupner SUMD.
Yuneec ST24.

Connectors

– JST-GH
– USB-C

Pin Headers

Yes – 8 Servo

Conformal Coating

No

Extended Testing and Burn In

No

Custom Carrier Board Support

No

LED

Yes (RGB)

Dimensions

Width: 36mm (1.42”)
Length: 36mm (1.42”)

Weight

9.09g (.31 oz)

Mounting Holes

4mm holes at 31.5mm spacing, Silicone grommets for m3 screws

Protector Case

Optional

Typical Platforms

-Multirotor
-Rover
-Fixed-Wing
-Boats
-Submarines
-VTOL
-Automatic Tractors
-Others

Compatibility

PX4 >1.13.0, Ardupilot

Firmware

The mRo Pixracer Pro is compatible with the following firmware:

ArduPilot
-ArduCopter 4.x
-ArduPlane 4.x
-ArduRover 4.x

PX4

-PX4 greater than v1.13.0 (master or beta only until v1.13.1 release)

Normal Usage Guide

-> BATT_VOLT_PIN= 14
-> BATT_CURR_PIN= 15

All connectors follow the Dronecode connector standard. All connectors are JST-GH.Pixracer Pro do not have a safety switch option, If there’s a need to have one a CAN switch is required.

Pinout

Use collapsible tabs for more detailed information that will help customers make a purchasing decision.

Ex: Shipping and return policies, size guides, and other common questions.

This site is protected by reCAPTCHA and the Google Privacy Policy and Terms of Service apply.


Recently viewed

"OUR HAPPY CUSTOMERS"

★★★★★

Top quality as ever at good prices. They deliver fast.

Thanks

Lily
Los Angeles, CA
★★★★★

Easy transaction! First time user, but would definitely buy again.''

Jake Wilson
★★★★★

Add customer reviews and testimonials to showcase your store’s happy customers.

Author's name
Los Angeles, CA
★★★★★

Items Exactly As Describes Very Quick to ship and Good Communication From Seller.

Miler
Los Angeles, CA
★★★★★

Great Services at Good Price Bought a Few Items and Have Never been disappointed.

jack
Los Angeles, CA